Do you know how to disable IPv6 in Windows 11? If not, don’t worry! We’re here to help.
In this blog post, we will walk you through the process of disabling IPv6 on your computer. This is a good idea if you are having problems with IPv6 or if you just want to disable it for testing purposes.
To fix various Windows 10/11 problems, we recommend Outbyte PC Repair:
This software will repair common computer errors, protect you from file loss, malware damage, hardware failure, and optimise your computer for peak performance. In three simple steps, you can resolve PC issues and remove virus damage:
- Download Outbyte PC Repair Software
- Click Start Scan to detect Windows 10/11 issues that may be causing PC issues.
- Click Repair All to fix issues with your computer's security and performance.
This month, Outbyte has been downloaded by 23,167 readers.
Let’s get started!
Disable IPv6 in Windows 11 Using Network Settings
The most straightforward way to disable IPv6 in Windows 11 is to use Network Settings. Here’s how you do it:
- On your Windows 11 system, click on Start and select Settings.
- Switch to the Network and internet settings on the left pane and select Advanced network settings.
- Next, click on More network adapter options under Related settings.
- Under Network Connections, right-click on your active network connection and select Properties.
- Now, under Wi-Fi Properties, uncheck Internet Protocol Version 6 (TCP/IPv6) under the Networking tab.
- This will disable the IPv6 in Windows 11
Disable IPv6 in Windows 11 Using Command Prompt
If you don’t want to use the Network Settings, you can also disable IPv6 in Windows 11 using the Command Prompt.
Here’s how you do it:
- On your Windows 11 system, launch Command Prompt with administrative rights by right-clicking on the Command Prompt icon and selecting Run as administrator.
- Once inside the Command Prompt, type in the following command one by one and hit enter to disable IPv6:
- netsh interface teredo set state disabled
- netsh interface ipv6 6to4 set state state=disabled undoonstop=disabled
- netsh interface ipv6 isatap set state state=disabled
- These commands will disable IPv6 in Windows 11.
Disable IPv6 in Windows 11 Using Windows PowerShell
You can also disable IPv6 in Windows 11 using Windows PowerShell. Here’s how you do it:
- Open the Start menu and type “Powershell” to launch PowerShell with administrative rights.
- To verify that IPv6 is enabled, enter the command below into PowerShell after it has opened. IPv6 is operational if the Enabled column is set to True: Get-NetAdapterBinding -ComponentID ms_tcpip6
- To disable the IPv6 protocol, enter the command below into PowerShell and hit enter: Disable-NetAdapterBinding -Name “Ethernet” -ComponentID ms_tcpip6. Replace “Ethernet” with the name of your network.
- Finally, to verify that the IPv6 is disabled for your selected network, again use the Get-NetAdapterBinding -ComponentID ms_tcpip6 command and check if the Enabled column is set to False.
Summing Up
So now you know how to disable IPv6 in Windows 11 using Network Settings, Command Prompt, and Windows PowerShell. We hope this tutorial has been helpful and that it has given you the knowledge and confidence to disable IPv6 on your system. If you have any further questions, comment down your queries.
No, there should be no noticeable changes if you disable IPv6 on your system, as most applications will still be able to communicate over IPv4. However, some applications may not work properly due to the lack of an IP address. If this is the case, you can re-enable IPv6 on your system.
Yes, you can disable IPv6 for individual network connections by using the Network Settings or the Command Prompt method mentioned in this blog post.
No, it is not recommended to disable IPv6 unless you are experiencing issues with the protocol or if you are testing something. If your system runs without any problems, then it is best to leave IPv6 enabled.
Yes, you can re-enable IPv6 at any time by reversing the steps taken to disable it. You can either use the Network Settings or the Command Prompt method to re-enable IPv6.
Peter is an Electrical Engineer whose primary interest is tinkering with his computer. He is passionate about Windows 10 Platform and enjoys writing tips and tutorials about it.
